# Parking brake stuck

Do not force the car to move or bypass its release interlocks. Compare the warning, electrical supply and evidence of mechanical sticking.

> This is symptom guidance, not a confirmed diagnosis. Inspection and vehicle-specific tests are needed before replacing parts.

## What you may notice
- Parking brake does not release normally
- Possible release warning or resistance to movement

## Understand the possibilities
### Parking brake not releasing
A mechanical cable, actuator or control fault can keep a parking brake applied. Interlocks and release procedures vary by model.

**What distinguishes it**
A parking-brake message and resistance to moving differ from engine revs flaring with free-rolling wheels.

**Safe observation**
From outside a parked, cooled vehicle, note warning messages and visible leakage. Do not road-test reduced braking or touch hot wheels and discs.

**After confirmation**
Do not force movement; professionally verify release command, supply and mechanical action before recovery or repair.

### Discharged or weakened 12 V battery
A weak 12 V supply may cause slow cranking on combustion vehicles, dim lights or failure to reach READY on an EV or hybrid. Voltage alone does not establish battery health.

**What distinguishes it**
Slow cranking and light dimming support this path more than normal-speed cranking.

**Safe observation**
With the vehicle off, look for obvious case damage or corrosion without touching terminals. Do not disconnect the battery with the engine running.

**After confirmation**
Test battery state, charging and connections; charge or replace only as appropriate for the vehicle.

### Caliper movement or brake drag
Sticking guides or a piston can produce uneven wear, squeal, pull or heat.

**What distinguishes it**
Persistent one-sided noise and pull support checking caliper operation; never touch a hot wheel to compare temperatures.

**Safe observation**
From outside a parked, cooled vehicle, note warning messages and visible leakage. Do not road-test reduced braking or touch hot wheels and discs.

**After confirmation**
Service the confirmed sticking component and inspect pads/discs and hydraulic condition.

## Checks you can make safely
- From outside a parked, cooled vehicle, note warning messages and visible leakage. Do not road-test reduced braking or touch hot wheels and discs.

## Leave these to a professional
- Do not reach into a running engine bay, work under an unsupported vehicle, bypass safety systems or open fuel, high-voltage or refrigerant circuits.

## Urgent signs
- Has braking weakened, does the pedal sink, or is there a fluid leak, smoke or a red brake warning?

Stop driving as soon as you can safely do so. Switch the vehicle off and obtain professional roadside assistance. Do not restart to investigate.

## When to get help
Arrange professional inspection. Share the conditions, warning messages and your answers; ask the workshop to confirm the cause before repair.

## Technical references
Sources explain general principles. Exact procedures and equipment depend on your vehicle. Editorial synthesis; no independent mechanic sign-off claimed.
- [HELLA: Checking the brakes](https://www.hella.com/techworld/en/technical/brakes/checking-the-brakes/)
- [Ford: Owner manual — maintenance information messages](https://www.fordservicecontent.com/Ford_Content/vdirsnet/OwnerManual/Home/Content?ProcUid=G1953908&Uid=G1953905&buildtype=web&countryCode=USA&div=f&languageCode=EN&userMarket=THA&vCode=&vFilteringEnabled=False&variantid=6125)
- [HELLA: Checking the starter](https://www.hella.com/techworld/en/technical/car-electronics-and-electrics/starting-and-charging-system/checking-the-starter/)
- [DENSO: Alternator troubleshooting](https://www.denso-am.eu/news/alternator-troubleshooting)
- [Ferodo: Brake noise — issues and solutions](https://www.ferodo.com/en-ca/technical/tech-tips/brake-noise-tips.html)

## A little more clarity
### Can this confirm the failed part?
This is symptom guidance, not a confirmed diagnosis. Inspection and vehicle-specific tests are needed before replacing parts.
